Equations are not being displayed properly on some articles. We hope to have this fixed soon. Our apologies.

Turtur, C. (2010). Proposal for a test of a motionless zero-point-energy converter. PHILICA.COM Observation number 61.

ISSN 1751-3030  
Log in  
Register  
  1138 Articles and Observations available | Content last updated 21 July, 12:05  
Philica entries accessed 3 165 413 times  


NEWS: The SOAP Project, in collaboration with CERN, are conducting a survey on open-access publishing. Please take a moment to give them your views

Submit an Article or Observation

We aim to suit all browsers, but recommend Firefox particularly:

Proposal for a test of a motionless zero-point-energy converter

Claus W. Turturconfirmed userThis person has donated to Philica (Fachbereich Elektrotechnik, University of Applied Sciences Braunschweig-Wolfenbuettel)

Published in physic.philica.com

Observation
Abstract:
The proposal describes tapping an unknown energy-source, told to operate years ago, but not yet reproduced. The principle is unexplained. The setup came from Prof. S. Marinov of Sofia University via a colleague at Vienna University. A setup has been confirmed by the TÜV-München.

Article body:
In 1989-91 the colleague reported about investigations on a special transformator consisting of magnets and coils.
(drawing: http://www.ostfalia.de/export/sites/default/de/pws/turtur/FundE/English/MLMC2.pdf)
The hysteresis loop was passed by applying a pulsed current to the primary coil. Surprisingly, the secondary coil was said to produce more electric power than the primary coil needed, depending on the pulse-width of the primary pulses. Discussion of the reason: Inertance of magnetization due to the Barkhausen-effect might delay the decrease of the magnetic flux in the magnets.
In 1990/91 the Austrian Engineer H. Schnelzer reproduced the setup using an electric circuit supplying short 7kAmp-pulses by IGBTs, sourced from a car-accumulator. At a demonstration at Scheibbs, 1500 people saw an output power of about 2.1kW (driving a heater and a lamp) for 90 minutes, i.d. more than 3kWh. But the accumulator only had 50Ah/12V, i.e. a power-capacity of maximal 0.6kWh. Furthermore the accumulator did not discharge. It is said, that the device has been inspected and certified by TÜV-München, by measuring input- and output-power and temperature.
Important is an air gap in the yoke as well as high current IGBTs (Driving those IGBTs is today easy doable with Analog Devices ADUM5230 (2.5kV) ADUM7234 (1kV) (Isolation rating), or other Isolated-Gate Drivers). The IGBTs (4 pieces, H-bridge-circuit) of Mr. Schnelzer had a turn-on time of 1µs / ~7000A at 1000V.

Authors: Johannes Horvath, Claus Turtur
Address: University of Applied Sciences Braunschweig-Wolfenbüttel
Salzdahlumer Str. 46/48
D - 38302 Wolfenbüttel
Email: c-w.turtur@ostfalia.de

Information about this Observation
This Observation has not yet been peer-reviewed
This Observation was published on 4th June, 2010 at 14:46:09 and has been viewed 8533 times.

Creative Commons License
This work is licensed under a Creative Commons Attribution 2.5 License.
The full citation for this Observation is:
Turtur, C. (2010). Proposal for a test of a motionless zero-point-energy converter. PHILICA.COM Observation number 61.


<< Go back Review this ObservationPrinter-friendlyReport this Observation



Website copyright © 2006-07 Philica; authors retain the rights to their work under this Creative Commons License and reviews are copyleft under the GNU free documentation license.
Using this site indicates acceptance of our Terms and Conditions.

This page was generated in 0.2974 seconds.